TENDA router product FAQs.
Q: I just bought a 6608 of your broadband router, why not enter the router settings page? What my computer need to set it? . .
A: the computer requires two settings.
1, the system network settings (windows xp for example). .
1, computer network settings there are two ways to specify the network IP address and automatically finds the IP address, normally we recommend the use of automatically finds the IP address, so you can avoid the errors that occur during Setup. If you need to set the IP address, that we can in the local area connection properties for the TCP/IP protocol addresses found in, and fill in the appropriate IP address. In the specify an IP address, you must specify the DNS domain name server, otherwise the page will not be able to browse.
Second, in determining the correctness of the system network settings, if in the IE address bar enter the IP address of the router settings page, landing had not been made, then we can check inside the IE browser options settings are set for our router state, we can IE's toolbar select "Tools" menu, then enter the "Internet Options", then select Internet Options inside "connection", see bottom of this page whether to connect dial-up connection which exists, if were removed, and then select "LAN Settings", there are three options LAN settings box is checked if both the cancellation of tick。.
Q: How do I make sure my computer and the router has been connected properly? . .
First of all please check both ends of the Ethernet cable is connected to the NIC interface and the LAN port of the router, and then check the NIC ports and router LAN ports on the corresponding led is normal. If the light is not working properly, please refer to why use longer twisted-pair network cable will not connect or is very slow. Determine the network driver is installed properly. And then in the computer checks the network connection: check that your network is connected, we recommend that you put the system in the network settings IP address to automatically obtain. Then if the system is win98 and wimme run at the run winipcfg, select your network card in the adapter to see whether the IP address and gateway access (which shall be the gateway address IP address of the router), if it is win2k, winxp system Please enter the command prompt (Start -> All Programs -> Accessories -> Command Prompt), then enter ipconfig see whether your network card IP address and gateway access.If address and gateway are correct, you can use ping to confirm: at a command prompt, type ping the default router IP (that is, the gateway address), example: ping .168.192.. .1 .1.
Q: Why use a long twisted pair cable may cause connection problems or very slow? . .
A: in the production of twisted-pair network cable, there are two standards: T568A and T568B, in practice, most of them use the T568B, generally considered the standard for electromagnetic interference shielding for the better. T568B standard 1 to 8 feet is defined as follows: with RJ-45 connector, clamp down on one side, you want to insert the cable ports to yourself, and then on top of the metal contacts from left to right are: 1 ~ 8, 8 different colors of the cable shall be conducted in accordance with the following sort order:.
1. . Orange White 2. . Orange 3. . Green White 4. . Blue 5. . Blue and White 6. . Green 7. . Brown White 8. . Brown. .
Q: can I put the computer to the specified IP address?.
A: Yes. But pay attention to each computer's IP address can not be repeated. (Specify the IP process, attention must specify the DNS). .
In Windows98/me.
1. Go to Control Panel, double-click Network. .
2. double-click the TCP/IP Protocol (corresponding to the card you are using it).
3. Click the specified IP address, enter 192. .168. . X. . Y (where X and routers, this bit the same, Y and router bit different here and in between 1-254). Enter 255 in the subnet mask. .255. .255. .0. .
4. click the default gateway, type the IP address of router (such as 192. .1 .1 .168...).
5. Click the DNS, select the Enable DNS, host name any (not with the same name within the network computer), add the local DNS server address (if do not know can fill in the router IP address). .
6. press OK twice, and then restart the computer.
In Windows 2K/XP in. .
1. Enter the Control Panel, double-click Network and dial-up connections.
2. . Double-click Local Area Connection, click the Properties button. Double-click Internet Protocol (TCP / IP). .
3. Click use the following IP address, and enter the IP address. 192. .168. .X, .Y's address (where x and router are the same as the bit Y and routers that bit different and is located between 1 and 254). In the subnet mask enter 255. .255. .255. .0.
4. . In the default gateway, enter the router IP address (such as 192. .168. .1. .1). .
5. The preferred DNS server and alternate DNS server is set to the local DNS server address, if you don't know can also be filled in with the router's IP address.
6. . And then the two can be determined. .
Q: I use Internet ADSL way, why after I set up the router cannot be used for dial-up dial-up software?.
A: set up the router's PPPoE connection is dial-up by the router, so you do not need to use the computer's dial-up software, simply set the computer to automatically obtain IP address or set up by the above method to set IP address on it. .
Q: why is the router cannot get into the wide area network address?.
A: Make sure your router WAN settings within the type is correct, check your router and cable broadband access (such as direct connections to the home cable or ADSL modem to connect out from the cable) are connected, the router's WAN port indicator is now on. Next, check whether your router is configured correctly and save the restart. (Special Note: If this is ADSL or Netcom users must determine the correct user name and password, otherwise difficult to find). .
Q: Why use MSN when prompted the computer behind the firewall?.
When you or the person to communicate with your firewall or network address translation devices (such as routers) after, the block that you are directly connected to the Internet. There needs to be you, or to communicate with your people to use the network address translation device supports UPnP, now the Royal TENDA Angel series, such as: 6608S/6611S/6617/6624, have to support UPnP, you only need to set the router When the UPNP set to open, you can actually network address translation function.Additionally supports UPnP system primarily for Windows XP and Windows ME. If you have only one computer needs to have a voice or video you can add this PC to DMZ host. More information on UPnP technology, please refer to the Microsoft Web site.
Q: If I set the server in the LAN (WWW, FTP, etc.) how to make the external network can access my server? . .
A: If you set up a server in the LAN, use the TENDA router port mapping features, like an Angel series sets the TENDA Royal virtual server is a very simple, you only need to enter into the router setup main page, select the virtual server, and then enter to enter the client PC's IP address, port, can software services please fill out the appropriate ports, following are some commonly used ports: FTP — 20, 21; 25; SMTP — HTTP — 80; 110; POP3 — — 22, PCANYWHERE, 5632 5631; MSN file transfer-6891-6900 . .
Q: what is a DMZ? how many router supports TENDA DMZ computer?.
A: The demilitarized zone (DMZ) is a firewall feature. It can make a particular computer to the Internet open. There. .
Some applications need to open multiple TCP/IP interface. The DMZ can implement these features. Each computer needs. DMZ.
To a different WAN IP address. At present, most of the routers can only support a DMZ computer. .
Q: I changed TENDA router's IP address/password, but since a long time, I've changed the password forgot, I ask how to re-enter Setup page?.
If you forget to change the password, you can reset the router to factory settings to the router settings back to default setting, then re-enter. .
Type the user name of the initial IP address initial password reset method of the initial.
6608S/6611S/6617/6624/6618/6690 so, reset the user name and password are admin. .
If I bought router fails, pay attention to when the warranty?.
Tenda you change routers, please note the instructions at the same time the power supply and replacement. Because sometimes a product temporarily out of stock or discontinued, which would require the replacement of other types of products, and other types of products of power and settings may vary, so be sure to also replace the power supply and manual. .
